Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing changed? Glance within the tank, and you could see no water inside. Before you panic, rest assured that repairing this challenge is usually straightforward. If you can’t figure it out yourself, you can always schedule toilet repair with a knowledgeable plumber. Follow these recommendations to diagnose and repair the problem of no water in the toilet tank. 

Check the Water Supply 

The first action is to ensure that the water is running. If you or someone in your household recently completed a toilet repair, you probably turned off the water first. Did you forget to turn it back on? To find out, spin the water shut-off valve on the wall behind the toilet. If the valve was turned off, water should now start refilling the tank. If this does not work, check the water at your sink or an alternative plumbing fixture. If nothing comes out from the tap, you could possibly have a bigger water supply issue. Contact your water company to find out more. 

Reposition or Replace the Float Mechanism 

Older toilet brands use a float ball to measure the water level as it rises in the tank. When the ball hits a certain height, the float arm it’s connected to stops the water flow. However, insufficient water might enter the tank if the ball is positioned wrong or the arm is faulty. To adjust the float ball, start by removing the toilet tank cover. Bend the float arm up a little to alter where it sits in the tank. If this fails to fix the problem, you might need to replace the full float mechanism. You should be able to complete this yourself by following the directions that come with the replacement parts, or you can hire a plumber for help. Just understand that float balls are old toilet technology. You may appreciate improved dependability and efficiency if you upgrade the existing tank components or replace the toilet altogether. 

Adjust the Fill Valve 

More recent toilets use a float cup instead of a float ball, coupled with a fill valve and water level rod. There may very well be no water in the toilet tank because the valve has slipped out of place or become plugged. Here are a few]] {tips to consider: 

• Adjust the fill valve: Have a look inside the toilet and find the fill valve on top of a vertical tube device on the left side of the tank. Ensure it’s secure and evenly attached to the tube. Then, fine-tune the water level. Current models of toilets have an adjustment knob you can turn by hand, while older models may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and make it possible for the tank refill to check the water level. Change it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube. 
• Clean the fill valve: Mineral buildup and other gunk might be clogging the valve and preventing your toilet from filling. Turn off the water behind the toilet and take off the fill cap. Then, slowly turn the water back on, cupping your hand over the valve to stop water from spraying everywhere. After several seconds, turn the water back off. Finally, scrub the fill cap to clear away hard water buildup. If the cap is cracked, buy a new one. 
• Clean the valve tube: The tube below the fill valve could also be clogged. Shut off the water and take away the valve hardware. Then, stick a slim bottle brush or wire down the tube. Turn the water back on slightly to flush away the blockage. Replace the valve hardware and flush the toilet to check your efforts. 

Repair or Replace the Trip Assembly 

If you’ve tried the steps above without any luck, the one remaining possibility is a faulty trip assembly. This part links the flush handle to the tank. If it’s broken or positioned improperly, the flush cycle may not complete, leaving the tank void. Take off the toilet tank lid and check the trip assembly attached to the handle. If it’s out of place, reposition it. If the assembly is bent, worn or broken, change it out. Whether you finish the job yourself or leave it to a plumber, this simple repair should get your toilet tank filled with water again. 

Schedule Toilet Repair Today 

You can’t go long without a functional toilet, so call [Company name] to inquire about a toilet repair. We can diagnose why your toilet isn’t filling and suggest the correct fix. If your plumbing fixture is outdated and worn out, our team can install a high-efficiency toilet in your bathroom. Rest assured that every plumbing repair and replacement we conduct is backed by a 100% satisfaction guarantee. To schedule an appointment from one of our licensed team members, please reach out to your local Bryant Heating & Cooling Service Experts office today.