How to Drain Your Water Heater: A Step-by-Step Guide

Tank water heaters are a reliable way to provide a fast supply of hot water for your home. The addition of a storage tank ensures some hot water is always available. But over time, foreign substances can accumulate inside the storage tank. This could be sediment or mineral buildup coming from the main water line or a flaw in the pipes. Whatever the source is, this buildup will sometimes reduce the efficiency of water heaters. In severe cases it can clog up drainage and could even lead to premature failure.

Thankfully, draining your water heater and clearing out sediment buildup is a relatively straightforward task. A certified plumber in Windsor can handle the process, but you can also drain the tank yourself if you know what you’re doing. Whatever you choose, draining the tank now can help minimize the risk you’ll need premature water heater replacement.

Before You Begin…

Before you start draining the tank, you should shut off the cold water supply. The supply valve connects your water heater with the main water line. Unless you have access to a well (and you may need to drain the tank more frequently if you do), the water main delivers all the potable water your home uses. Keeping the valve shut will stop more water from reaching the tank, allowing you to completely empty it.

You’ll also want to have a rubber hose, like one you could use for yard work. The hose allows you to safely drain the water heater tank without spilling water all over your garage, utility closet, attic or wherever the water heater is kept. Make sure you leave the other end of the hose far away from your home to keep the water from seeping back inside.

Finally, a screwdriver will help you loosen tight screws or valves. You shouldn’t need any more tools than this unless you discover a problem with the water heater or nearby piping. At that point, it might be best to contact a certified plumber in Windsor.

Step 1: Shut Off the Water Heater

After you’ve shut off the water supply, you can shut off the water heater itself. This should be on the thermostat for natural gas water heaters or with a breaker switch for electric models. The pilot setting on gas water heaters can continue to stay on during flushing, but electric models must be completely off. This is due to the heating elements electric water heaters use, which remain submerged. In an empty tank, they could quickly overheat. You should also review the model’s manual, as some water heaters must be completely full before the heating elements are turned on.

Even after you’ve shut off the water heater, you’ll have to wait for the water stored in the tank to cool down. It could be hours before the water cools to a safe temperature, so it is often best to leave the rest of the process for the following day.

Step 2: Connect the Hose to the Water Heater’s Drain Valve

Tank water heaters are designed with a drain valve you can use to empty the storage tank. Once you’re sure the water supply is disconnected and the water heater itself is off, locate the drain valve. Some models will have it covered up. Make sure the hose is securely fastened to prevent spilling hot water near you and the water heater.

Step 3: Open a Faucet or Other Hot Water Tap

Your home’s plumbing takes advantage of pressure within the piping to sustain a consistent flow of water from the main water line to the rest of the house. This pressure needs to be relieved before the hot water can actually drain out of the tank. By heading to the nearest faucet or spigot, you’ll release the pressure inside the piping. All you have to do is open the hot water tap to relieve the pressure before heading back to the water heater.

Step 4: Release the Drain Valve

Don’t forget that this water might still have some residual heat. Open the drain valve and allow all the water to drain from the tank. This should pull sediment buildup out of the tank and away from your home. But some buildup may be stuck to the inside of the tank. Turning the cold water supply back on will help flush stubborn minerals and other substances from the tank.

Repeat this step until the water looks clear of sediment or minerals. If the drain isn’t working because of a clog, a trained plumber is likely required.

Step 5: Re-Shut the Valve Before Refilling the Water Heater

If everything proceeds like it’s supposed to, you should be able to take care of most excess sediment hiding inside your water heater. Seal up the drain valve, disconnect the hose and open the water supply to get things flowing again. As the water heater tank begins to fill, return to the hot water tap you opened. Once cold water starts to flow, you know the pressure is back where it needs to be.

At this point, you can open the gas valve or flip the breaker switch back on. Like we mentioned earlier, don’t forget that some models may need to be totally full before the water can be safely heated. Make sure you check your manufacturer’s instructions before starting the process.

Keep Your Water Heater Sediment-Free for Best Results

Tank water heaters continue to be a great option for supplying your hot water needs. Draining the tank every 1-2 years will help clear out sediment buildup and keep things running at peak efficiency. If you think your water heater is past the point of efficient heating, consider looking for water heater replacement in Windsor from a technician you trust.